SIMPLE   =  F
PROJECT  = 'GW'
SYSTEM   = 'OPS'
FLIGHT   = 1
INSTRUME = '3D Plasma'
ORIGIN   = 'UC Berkeley'
OBSERVER = 'Peter Schroeder'
DESC     = 'Full configuration: 3 processor'
COMMENT     WARNING!!  approximately 160 commands uplinked!!!
COMMENT     RUN TIME 45 minutes
COMMENT     REQUIRES P3DMCFG0-3.MAC  ON SPACECRAFT
COMMENT     REQUIRES P3DECFG0-2.MAC  ON SPACECRAFT
COMMENT     REQUIRES P3DPCFG0-1.MAC, P3DPHSW0-1.MAC  ON SPACECRAFT
COMMENT     Does NOT load SST Calibration table and Hi/Quiet test
COMMENT     FPC and ESA PHAs disabled
COMMENT     Configuration date: 2007-Oct-08
FILENAME = 'P3D131A'
FILETYPE = 'RTC'
DATE     = 'May 27, 2021'
VERSION  = 1
HAZFLAG  = F
URGENT  =       F       ;microload associated
CMSSAVE =       T       ;save file after uplink
END

;Peter Schroeder (510-828-2933)
;No need to contact me during the pass unless you see
;something unusual/scary.
;Note: The HV enable commands are hopefully redundant,
;that is we believe they are already enabled, but we
;include the commands to be completely sure.

/I_P3D_MAJ KEPQUIET_A                ;Always Required
/SEND

;Wait 10 seconds

/I_P3D_MIN MAIN_MMC X'D' X'18800FF'    ;System Burst trigger Disable
/I_P3D_MAJ CLEAR_ER_A                ;PESA CFG:  37 commands
/SEND

;Wait 10 seconds

/I_P3D_MIN PESA_MMC X'D' X'0060077'    ;config ID PPESAVER=x'77'
/SEND

;Wait one minute

/EXEC P3DPCFG0.MAC                   ;Blip (TFCMND) patch  7700-777Fx
/SEND

;Wait two minutes

/EXEC P3DPCFG1.MAC
/SEND

;Wait two minutes
                   ;
/EXEC P3DPHSW0.MAC                   ;Pesa-H Short sweep patch  7780-77ffx
/SEND

;Wait two minutes

/EXEC P3DPHSW1.MAC
/SEND

;Wait two minutes

/I_P3D_MAJ CLEAR_ER_A                ;Clear errors, P_CMDS = X'00'
/SEND

;Wait 10 seconds

/EXEC P3DPT8A.ACT                    ;KP flux patch + Burst trigger 66 cmnds
/SEND

;Wait 4 minutes

/I_P3D_MAJ CLEAR_ER_A                ;Clear errors, P_CMDS = X'00'
/I_P3D_MIN PESA_MMC X'D' X'1307700'    ;link BLIP patch :user_init_ptr
/I_P3D_MIN PESA_MMC X'D' X'0440025'    ;HK packet time: TLM load balance
/I_P3D_MIN PESA_MMC X'B' X'0727863'    ;patch PT8A Density Trigger:down check:96:122
/I_P3D_MIN PESA_MMC X'D' X'30E7780'    ;LINK PHsweep patch
/I_P3D_MIN PESA_MMC X'D' X'378780A'    ;link Burst trigger
/I_P3D_MIN PESA_MMC X'D' X'37A7800'    ;link KP low flux patch
/I_P3D_MIN PESA_MMC X'D' X'3100343'    ;Short sweep Starting sector#
/I_P3D_MIN PESA_MMC X'D' X'342B9AF'    ;PESA MCPL=2730 (B9); MCPH=2630 (AC)
/I_P3D_MIN PESA_MMC X'D' X'3440040'    ;Pesa-H Interplanetary sweep: no low E sun look
/I_P3D_MIN PESA_MMC X'D' X'35CF6AE'    ;Pesa-H Solarwind K=63150
/I_P3D_MIN PESA_MMC X'D' X'27E005E'    ;CBIN  95:009
/I_P3D_MIN PESA_MMC X'D' X'2830003'    ;Set alpha_step to 3
/I_P3D_MIN PESA_MMC X'D' X'38A01F4'    ;Brst_Log_offset: 500
/I_P3D_MIN PESA_MMC X'D' X'38C0719'    ;Dv Filter=7, NV_THRESH=25  Burst trigger setup
/I_P3D_MIN PESA_MMC X'D' X'38E6403'    ;Velocity Trig=100,Fil=3/7
/I_P3D_MIN PESA_MMC X'D' X'39CD65D'    ;map_45d: 22d map
/I_P3D_MIN PESA_MMC X'D' X'39ED4A4'    ;map_bst: 11d map
/I_P3D_MIN PESA_MMC X'D' X'3B86000'    ;PH accums 1/64, 63/64  int_period
/I_P3D_MIN PESA_MMC X'D' X'3BA5500'    ;PH S1X Norm:32/32 Bst:1/1
/I_P3D_MIN PESA_MMC X'D' X'3BC6000'
/I_P3D_MIN PESA_MMC X'D' X'3BE5500'    ;PH S1XB Norm:32/32 Bst:1/1
/I_P3D_MIN PESA_MMC X'D' X'3C04400'    ;
/I_P3D_MIN PESA_MMC X'D' X'3C24400'    ;PH S2X    Normal: 16/16  Burst: 1/1
/I_P3D_MIN PESA_MMC X'D' X'3C45500'    ;
/I_P3D_MIN PESA_MMC X'D' X'3C64400'    ;PH S2XB   Normal: 16/16  Burst: 1/1
/I_P3D_MIN PESA_MMC X'D' X'3C8AA99'    ;BTS_C_VAL:  16 COUNTER MAX
/I_P3D_MIN PESA_MMC X'D' X'2D20014'    ;ph_bst_shft: Rotate 45 degs
/SEND

;Wait 5 seconds

/I_P3D_MAJ HV_ENA_PSA                ;ENABLE PESA HIGH VOLTAGE
/SEND

;Wait 5 seconds

/I_P3D_MAJ CLEAR_ER_A                 ;EESA CFG: 16 commands
/SEND

;Wait 5 seconds

/I_P3D_MIN EESA_MMC X'D' X'0060077'     ;config ID PMAINVER=x'77'
/SEND

;Wait 5 seconds

/EXEC P3DECFG0.MAC                    ;7A00: EESA MOMENTS OVERFLOW PATCH
/SEND

;Wait 2 minutes

/EXEC P3DECFG1.MAC                    ; SciParm x:017A : x:6C-EC
/SEND

;Wait 2 minutes

/EXEC P3DECFG2.MAC                    ; SciParm x:0216 : x:9C-EC
/SEND

;Wait 1 minute

/I_P3D_MAJ CLEAR_ER_A                 ;Clear errors, P_CMDS = X'00'
/SEND

;Wait 5 seconds

/I_P3D_MIN EESA_MMC X'D' X'1988A80'     ;New pointer to c1 buffer
/I_P3D_MIN EESA_MMC X'D' X'19A9F80'     ;New pointer to c2 buffer
/I_P3D_MIN EESA_MMC X'D' X'37C7A00'     ;LINK Moments PATCH
/I_P3D_MIN EESA_MMC X'D' X'380F2B0'     ;DISABLE BURSTS
/I_P3D_MIN EESA_MMC X'D' X'33A921C'     ;pmt  no deflectors
/I_P3D_MIN EESA_MMC X'D' X'33CA780'     ;McpH=2240V (80) McpL=2905V (A7)
/I_P3D_MIN EESA_MMC X'D' X'34C1FA4'     ;E0=8100   EESA LOW 95:055
/I_P3D_MIN EESA_MMC X'D' X'34EF104'     ;k=61700   STD
/I_P3D_MIN EESA_MMC X'D' X'3520274'     ;s2=628
/SEND

;Wait 5 seconds

/I_P3D_MAJ HV_ENA_ESA                 ;ENABLE EESA HIGH VOLTAGE
/SEND

;Wait 2 minutes

/I_P3D_MAJ CLEAR_ER_A                 ;MAIN CFG: 30 commands
/SEND

;Wait 5 seconds

/I_P3D_MIN MAIN_MMC X'D' X'0060077'     ;main_config ID PMAINVER=x'77'
/SEND

;Wait 5 seconds

/EXEC P3DMCFG0.MAC                    ;7200: SST TLM table,Patch Linker
/SEND

;Wait 2 minutes

/EXEC P3DMCFG1.MAC                    ;7240: burst Nibble compression patch
/SEND

;Wait 2 minutes

/EXEC P3DMCFG2.MAC                    ;7400: burst patch Part 1
/SEND

;Wait 2 minutes

/EXEC P3DMCFG3.MAC                    ;7458: burst patch Part 2
/SEND

;Wait 2 minutes

/I_P3D_MAJ CLEAR_ER_M                 ;Clear errors, P_CMDS = X'00'
/SEND

;Wait 5 seconds

/I_P3D_MIN MAIN_MMC X'D' X'3567200'     ;Link Tlm table
/I_P3D_MIN MAIN_MMC X'D' X'3107210'     ;autolinker for patches
/I_P3D_MIN MAIN_MMC X'D' X'0070067'     ;Enable burst system
/I_P3D_MIN MAIN_MMC X'8' X'000071F'     ;Flush burst system
/SEND

;Wait 10 seconds

/I_P3D_MIN MAIN_MMC X'D' X'17A02AA'     ;Pre-event buffers 682 pkts
/I_P3D_MIN MAIN_MMC X'D' X'17C02AA'
/I_P3D_MIN MAIN_MMC X'D' X'17E02AB'
/I_P3D_MIN MAIN_MMC X'D' X'1800400'     ;Event buffers 1024 pkts
/I_P3D_MIN MAIN_MMC X'D' X'1820400'
/I_P3D_MIN MAIN_MMC X'D' X'1840000'     ;FPC disabled: no buffer
/I_P3D_MIN MAIN_MMC X'8' X'0000F1F'     ;Reconfigure burst allocation
/I_P3D_MIN MAIN_MMC X'D' X'08A0064'     ;Minimum Burst duration = 100 spins
/I_P3D_MIN MAIN_MMC X'D' X'3240A08'     ;F5:F1   SST Thresholds :WORD order!
/I_P3D_MIN MAIN_MMC X'D' X'3260807'     ;F3:F4   (reversed bytes)
/I_P3D_MIN MAIN_MMC X'D' X'3280E4C'     ;O5:O1
/I_P3D_MIN MAIN_MMC X'D' X'32A0908'     ;O3:O4
/I_P3D_MIN MAIN_MMC X'D' X'32C0705'     ;F6:F2
/I_P3D_MIN MAIN_MMC X'D' X'32E1708'     ;O6:O2
/I_P3D_MIN MAIN_MMC X'D' X'3300C07'     ;T6:T2
/I_P3D_MIN MAIN_MMC X'D' X'2320061'     ;HV=95v @ .977v/count
/I_P3D_MIN MAIN_MMC X'D' X'3350805'     ;Burst filter   95:027
/I_P3D_MIN MAIN_MMC X'D' X'337FFFF'     ;O/F Burst threshold:  Disable
/I_P3D_MIN MAIN_MMC X'D' X'33C027E'     ;1 Slice Blanking
/SEND

;Wait 10 seconds

/I_P3D_MAJ HV_ENA_SST                 ;Insure SST HV is on
/SEND

;Wait 2 minutes

/I_P3D_MIN MAIN_MMC X'E' X'0E57000'     ;Confirm Pre reset configuration,patches
/SEND

;Wait 1 minute

/I_P3D_MIN EESA_MMC X'E' X'0E17A00'     ;EESA eMom patch + config
/SEND

;Wait 1 minute

/I_P3D_MIN PESA_MMC X'E' X'0E27700'     ;PESA Patches + config
/SEND

;Wait 1 minute

/I_P3D_MAJ CLEAR_ER_A                 ;Clean up error messages
/SEND

;Wait 10 seconds

/I_P3D_MAJ SOF_RSET_M                 ;RESET ALL
/SEND

;Wait 7 minutes

/I_P3D_MAJ KEPQUIET_A                 ;quiet after all configured
/SEND

;Wait 10 seconds

/I_P3D_MIN MAIN_MMC X'D' X'1880003'     ;System Burst trigger enable
/I_P3D_MIN MAIN_MMC X'E' X'0E57000'     ;Confirm Post reset configuration,patches
/SEND

;Wait 1 minute

/I_P3D_MIN EESA_MMC X'E' X'0E17A00'     ;EESA eMom patch + config
/SEND

;Wait 1 minute

/I_P3D_MIN PESA_MMC X'E' X'0E27700'     ;PESA Patches + config
/SEND

;Wait 1 minute

/I_P3D_MAJ RESUME_ALL                 ;restart data
/SEND